3785/COMPASS/PRESS/JS/23-Press for COMPASS (Composites at Speed and Scale) Facility - AWARD

Contract summary

Industry

• Presses - 42636000

• Hydraulic presses - 42636100

Location of contract

S60 5TZ

Value of contract

£0 to £3,600,000

Procurement reference

IT-40-3488-3785/COMPASS/PRESS/JS/23 - AWARD

Published date

19 December 2023

Closing date

29 September 2023

Closing time

12pm

Contract start date

20 October 2023

Contract end date

19 October 2026

Contract type

Supply contract

Procedure type

Open procedure

Contract is suitable for SMEs?

Yes

Contract is suitable for VCSEs?

No

---

Description

3785/COMPASS/PRESS/JS/23-Press for COMPASS (Composites at Speed and Scale) Facility

The University of Sheffield wishes to invite tenders for a 'Press' on behalf of the Advanced Manufacturing Research Centre, Castings Group at Catcliffe, South Yorkshire.

Scope of Requirement
The AMRC has recently won funding for an 'automated, large scale composites manufacturing centre', including a 'fully automated layup and consolidation cell' which will incorporate a 10.5m (length) x 3.5m (width) x 2.3m (daylight) Press.

Within the 'Fully Automated Layup and consolidation cell' the Press will sit alongside a variety of other equipment, and will be in close proximity to the following:-
o High Volume Deposition Cell - including Robot arms and guide rails;
o Press Heater System;
o Press Injection System;
o Oven Feed table.

The Press is to be used for manufacturing research into the production of large polymer composite components using several potential processes, including (but not limited to):-
o Dry fibre pre-forming;
o Resin Transfer Moulding (RTM);
o Gap RTM/ Infusion;
o Wet Compression Moulding and Compression Moulding of pre-preg.

Brief Summary of Requirements
Please see G1, G2, G3, G4 and G5 for our exact technical and functional requirements, however at a high level these can be summarised as:-
o The Press will have cold platens and that any heating for processing will be applied to the tooling rather than through the platens. A system of automated tool clamping, and location will need to be included within the tendered press platen package.
o The Press is expected to have a stroke of a minimum of 1500mm within the minimum daylight of 2.3m.
o The Press is required to have a moving lower platen that will enter and exit along the long axis from one end only. All controls and connections for the lower tool will remain active when the lower platen is fully extracted from the press.
o The AMRC is looking for flexibility in the size of tooling that can be used within the Press. The maximum size of component is defined for the purpose of this specification as 10m (length) x 3m (width) x 1.5m (depth) and this will require a minimum programmable force of up to 8 bar across the entire area of that part. Cost options for an incremental increase of this force up to 20 bar are requested (if possible).
o It is anticipated that the platens' size will exceed the maximum component size by approx. 0.5m in the X and Y axes (10.5m x 3.5m) to accommodate a part of 10m x 3m. To this end the tenderer is expected to recommend a suitable platen size within its proposal.
o The Press must be able to control the platens in a way that allows for tools shorter than the full length to be safely used. The limits to this function must be stated within your tender response.
o The Press will be expected to maintain the platens in an accurate Z plane whilst holding a full-sized tool open against a to...

---

Award information

Awarded date

1 December 2023

Contract start date

20 October 2023

Contract end date

19 October 2026

Total value of contract

£3,330,000

This contract was awarded to 1 supplier.

Langzauner GmbH

---

About the buyer

Contact name

Jamie Shaw

Address

Wallis Way
Catcliffe
Rotherham
S60 5TZ
United Kingdom

Telephone

01142221516

Email

jamie.shaw@sheffield.ac.uk